Installation is straightforward, the product comes with the necessary mounting brackets. Each side-by-side UTV fan can be tilted left/right manually and angled forward/back via the bracket. Direct cool air precisely to the driver and passenger seats for balanced, personalized comfort.

The fan is rated IPX6 for protection against dust and water jets, so it’s fine in rainy conditions. However, remove the fan during high-pressure washing to prevent potential damage from the intense water pressure.

It needs to be wired directly to your vehicle’s 12V electrical system. It does not come with a cigarette lighter plug. Connect the red wire to the positive or ACC terminal, and connect the black wire to the negative terminal.

For vehicles with a low dome like the X3 or MR, it is recommended to buy the version of single-head fan(B0502-00002-BK). This dual fan fits UTVs with a roof width between 41.3″ and 57.1″ and adequate headroom, such as Polaris Ranger, RZR XP 1000 (2024+), Can-Am Defender.

No, it is not compatible with golf carts.

We don’t recommend using it with the vehicle engine off. Its runtime depends on the battery condition.

The stand for this fan is made of iron.

Fits UTVs with a roof width from 41.3 inches to 57.1 inches. Additional accessories, doors and aftermarket roof setups may cause fit issues. If you are not sure about the vehicle compatibility, you could contact us through support@kemimoto.com to provide year+brand+model+submodel of your vehicle and some photos to show the additional accessories on your vehicle so that we could help come compatibility before the purchase.

Please contact us through support@kemimoto.com and send us some photos to show the parcel status, all the stickers on the package and the part damage issue directly. We will arrange replacement part after confirmation of the issue.

If you are willing to communicate and provide detailed issues and specifications, we can customize the product for free based on your needs and send it to you for testing. Please contact us through support@kemimoto.com and send us more details of the year+brand+model+submodel of your vehicle and the requirements of types you would like.

Yes, it includes a white LED dome light for bright cabin illumination at night. It does NOT have RGB halo lights, so you cannot change colors or sync with music. If you would like the one with RGB halo lights, then you could purchase B0502-00004-BK.

Yes. There are 2 knobs, one for adjusting the left fan speed, and the another one for adjusting the right fan speed.

First, confirm you have set the fan to the highest speed setting (Level 5/S5). If airflow is still insufficient, possible causes include: ① Blocked air intake; ② Unstable power supply voltage; ③ Fan is positioned too far from the occupant area. If you need stronger airflow, please stay tuned for our newly improved models.

If the lights are not working or behaving abnormally, please first confirm: ① Power connections are secure; ② The light switch is being operated correctly (some models have independent light switches). If the issue persists, please send us a video showing the problem, and we will determine whether to send replacement parts or a full unit.

Please confirm you are following the manual correctly: This product uses button/knob-based speed control, with each press cycling through speeds (S1-S5). If the display shows no change or the fan speed remains constant, please check: ① Whether the control box has been exposed to moisture or water; ② Whether all wiring connections are secure. If the issue persists, please send us a video for troubleshooting.

Please follow these troubleshooting steps:

① Confirm you are using a 12V DC power source and that the positive/negative terminals are correctly connected;

② Check if the fuse is blown;

③ Inspect cables for damage or loose connections;

④ Verify power is reaching the control box.

If all checks pass but the fan still doesn’t work, please send us a short video showing the issue for further assistance.

Some wind noise and motor sound at high speeds are normal. However, if you hear high-pitched squealing, grinding, or clicking sounds, there may be an issue. Please: ① Check if fan blades are contacting the shroud; ② Check for foreign objects (e.g., zip ties, wires) caught inside the fan; ③ Ensure mounting bolts are not over-tightened or too loose. If the issue persists, please send us a video for diagnosis.

The product includes both 40mm and 52mm hinged hose clamps. Please select the clamp that matches your roll cage tube diameter. If neither fits, please provide: ① A photo showing the tube diameter measurement; ② Clear photos of the mounting area. We will evaluate whether alternative clamps need to be sent.

Some wind noise and motor sound at high speeds are normal. However, if you hear high-pitched squealing, continuous grinding, or clicking sounds, there may be an issue. Please follow these steps:

1.Power off the unit and check if the fan blades are contacting the shroud or guard;

2.Check for foreign objects (e.g., zip ties, wire fragments, small debris) caught inside the fan;

3.Check if the mounting bolts are over-tightened or too loose – over-tightening can stress bearings, while looseness can cause rattling.
If the issue persists, please contact us through support@kemimoto.com and send us a video showing the problem. We’ll provide further help.

First, please confirm you have set the fan to the highest speed setting. If airflow is still insufficient, possible causes include:

1.Blocked air intake – check if the roof liner or wiring is obstructing the fan inlet;

2.Unstable power supply voltage – low voltage will reduce fan speed, please make sure the voltage to be 12V;

3.Fan positioning – adjust the fan angle to point directly toward the driver and passenger areas.
If you’ve checked all above and still find the airflow inadequate, please further contact us through support@kemimoto.com and send a video to show the issue directly.

Please first check the following:
1.Confirm the independent light switch is being operated correctly – some models have separate controls for lights and fans;
2.If the light stays on and cannot be turned off, it may be due to a short circuit caused by moisture – have you recently washed the interior of your vehicle with water?
3.If the light doesn’t turn on at all, check if the wiring harness between the control box and the light module is securely connected.
If the issue persists, please contact us through support@kemimoto.com and send us a video showing the abnormality. We’ll provide further help after confirmation on the item issue.

Please first confirm you are operating it correctly: This product uses button/knob-based speed control – each press or rotation cycles through speeds.
If the operation is correct but there’s no response, please check:
1.Whether the control box has been exposed to moisture or water – this can cause button failure;
2.Whether the wiring harness between the control box and fan motor is securely connected;
3.Try powering off and restarting the unit to see if it resets.
If the issue persists, please contact us through support@kemimoto.com and send us a video showing your operation and the item issue for further diagnosis.

This is usually caused by insufficient tightness of the pivot bolts. Please try:
1.Tighten the pivot bolts on both sides of the fan to increase friction and hold the angle;
2.Be careful not to over-tighten – this may cause the fan blades to contact the shroud and create noise;
3.If the issue persists after adjustment, please contact us through support@kemimoto.com and send a video to show the issue directly so that we could come up with further help.

A repeatedly blown fuse is usually caused by circuit overload or a short circuit. Please follow these steps:
1.Check if the fan blades are blocked by debris – a stalled motor will draw excessive current;
2.Inspect all wiring for damage, exposed conductors, or contact with the vehicle frame – this can cause a short circuit;
3.Confirm your vehicle’s power supply voltage is stable and within the 12V rating;
If all checks pass, please further contact us through support@kemimoto.com and send a video to show the voltage connection status and the item issue.

Please cut off power immediately and stop using the fan.

This is usually caused by motor overload or an internal short circuit. Possible causes include:
1.Fan blades are blocked by debris, causing the motor to stall and draw excessive current;
2.Motor bearings are seized, leading to overload and overheating;
3.Damaged wiring causing a short circuit.
4.Over-voltage.
Do not continue to power on the unit for testing, as this may cause further damage or safety hazards. Please further contact us through support@kemimoto.com and send us some photos to show your wiring setup, the connected voltage, and the item issue. We will further help check the issue and provide help.

Please cut off power first, then follow these steps:
1.Check if the fan blades are blocked by foreign objects (e.g., zip ties, wire fragments, small debris);
2.Gently spin the blades by hand – if you feel significant resistance or grinding, the bearings may be faulty;
3.Check if the blades are contacting the shroud or guard – the mounting may have shifted.
If the blades still won’t spin freely after removing any obstructions, please send us a video showing the blade condition for further assistance.

This is usually caused by interference between the clamps/mounting brackets and your doors or overhead audio system. Please:
1.Send us clear photos of the mounting area – we’ll help assess if there’s an alternative installation approach;
2.If the clamps are interfering with the door seal, try adjusting the clamp angle or position slightly;
3.Please note: This fan is designed as a universal-fit product. Roof structures and door designs vary by vehicle model, and some aftermarket modifications may require additional adjustments.